40
http://www.minebea-mcd.com http://www.minebea-mcd.com
41
Techno Graph Techno Graph
* Desk shown for illustration only. *Test Fixture, PC and software are optional.
Universal testing machine providing high accuracy with simple operation TGE series ● High accuracy
● High performance and simple operation
● Light weight and compact
Accuracy is ±1 % (JIS 1 class) of the indicated value from 1/1 ~ 1/500 of load cell capacity.
±0.5 % (JIS 0.5 class) is available as an option
Automatic load cell span adjustment, One-touch auto-zero, Auto-return to test start (No overshoots),
Test condition registration, Manual 3 level speed setting, Analog output of test force and position.
Corresponds to the tension/compression continuous repeat test.
Improved model, weight reduced by 50 kg and width reduced by 100 mm from earlier model.
*1) The measuring range changes depending on the capacity of the installed load cell. *2) The stroke extension type and the effective width expansion type are produced.
JCSS：MINEBEA is a recognition trader of JCSS of one shaft tester (Metric Method Traceability System).
P/No.
Measuring range *1)
Measuring accuracy
Applicable standard
Effective testing width *2)
Cross head stroke
Tension stroke
Cross head speed
Setting method of speed
Manual speed
Testing mode
Display
Standard installed function
Outline dimensions
Weight
Power supply / Power consumption
Operating temp./Humidity range
(mm)
(mm)
(mm)
(mm/min)
(mm)
(Approx. kg)
Techno Graph Techno Graph
* Desk shown for illustration only.
*Test Fixture, PC and software are optional.
Universal testing machine providing high accuracy with simple operation TGI series ● High accuracy
● High performance and simple operation
● Four highly accurate times in resolution from past servo motor
Accuracy is ±1 % (JIS 1 class) of the indicated value from 1/1 ~ 1/1 000 of load cell capacity.
±0.5 % (JIS 0.5 class) is available as an option.
Automatic load cell span adjustment, One-touch auto-zero, Auto-return to test start position (No
overshoots), Test condition registration, 3 level of manual speed setting, Analog output of test force
and position. Corresponds to the tension / compression continuous repeat test.
The accuracy of the position control has been greatly improved, and the stable driving in a low speed
region becomes possible.
*1) The measuring range changes depending on the capacity of the installed load cell. *2) The stroke extension type and the effective width expansion type are produced.
*3) The length of tension stroke is the condition in mounting the load cell and chuck for maximum testing capacity. JCSS：MINEBEA is a recognition trader of JCSS of one shaft tester (Metric Method Traceability System).
P/No.
Measuring range *1)
Measuring accuracy
Applicable standard
Effective testing width *2)
Cross head stroke *2)
Tension stroke *3)
Cross head speed
Return speed
Display
Standard function
Outline dimensions
Weight
Power supply / Power consumption
Operating temp./Humidity range
(mm)
(mm)
(mm)
(mm/min)
(mm)
(Approx. kg)
The return speed can be arbitrarily set in the range from 0.1 ~ 1 500 mm/min (10kN
or less) or from 0.1 ~ 750 mm/min (50kN or more).
●
0.000 5 ~ 500 mm/min
(Setting between 0.1 ~ 500 mm/min can be made by 0.1 mm/min
pitch. Setting under 0.05 mm/min can be made by 9 steps of
0.05, 0.03, 0.02, 0.01, 0.005, 0.003, 0.002, 0.001 or 0.000 5.)
TGI-10kN
0.05 N ~ 10 kN
715
(with CH/CHT-10kN)
TGI-5kN
0.05 N ~ 5 kN
825
(with CH-5kN)
TGI-1kN
0.05 N ~ 1 kN
870
(with CH-1kN)
TGI-500N
0.05 N ~ 500 N
900
(with CH-1kN)
TGI-200N
0.05 N ~ 200 N
920
(with CH-200N)
within ±1 % of indicated value from 1/1 to 1/1 000 of load cell capacity for tension and compression (±0.5 % of indicated value is available as an option)
1 or 0.5 class of JIS B 7721, class 1 or 0.5 of ISO7500-1, Class 1 of ASTM E4
Test force: 5 digits display ±99 999, Peak and Rupture testing power can be displayed. Position: 6 and 1/2 digits ±1 999.999,
Accuracy: within 0.1 % of indicated value.
Temperature 5 ℃ ~ 40 ℃, Humidity : 20 % ~ 80 %RH (No condensing)
TGI-250kN
0.05 N ~ 250 kN
600
1 550
630
(with CH/CHT-250kN)
1 400 x 2 450 x 894
1 200
TGI-100kN
0.05 N ~ 100 kN
600
1 350
860
(with CH/CHT-100kN)
1 221 x 2 192 x 720
900
TGI-50kN
0.05 N ~ 50 kN
420
1 015
480
(with CH/CHT-50kN)
900 x 1 507 x 490
310
420 (with protect cover for lead screw)
1 090
700 x 1 583 x 513
100
Three phase AC200 V~230 V,
5 kW at maximum
Three phase AC200 V~230 V,
7.0 kW at maximum
It can be set arbitrarily in the range from 0.1 ~ 750 mm/min
Load cell capacity : Auto adjust, Load cell span : Auto set for tension / compression, Zero point : One push, Position reset : One push, Operation
detected sample rupture : Selectable from either stop, reverse or ignore, Rupture detectivity : arbitrary set with 0.04 % to 99.00 % of the test force,
Test condition registration : 10 conditions, Analog output of test force and position : DC0 V to ±DC5 V (with scaling function), Communication
function : Conforming to USB interface 2.0/1.1 standard.
Single phase AC100 V ~ 115 V,
400 W at maximum. Three phase AC200 V~230 V, 750 W at maximum
0.000 5 ~ 1 000 mm/min
(Setting between 0.1 ~ 1 000 mm/min can be made by 0.1 mm/min pitch. Setting under 0.05 mm/min
can be made by 9 steps of 0.05, 0.03, 0.02, 0.01, 0.005, 0.003, 0.002, 0.001 or 0.000 5.)
It can be set arbitrarily in the range from 0.1 ~ 1 500 mm/min
Three phase AC200 V~230 V,
2 kW at maximum
TGE-10kN
0.1 N ~ 10 kN
715
(with CH/CHT-10kN)
TGE-5kN
0.1 N ~ 5 kN
825
(with CH-5kN)
TGE-1kN
0.1 N ~ 1 kN
870
(with CH-1kN)
TGE-500N
0.1 N ~ 500 N
900
(with CH-1kN)
TGE-200N
0.1 N ~ 200 N
920
(with CH-200N)
TGE-250kN
0.1 N ~ 250 kN
600
1 550
630
(with CH/CHT-250kN)
1 400 x 2 450 x 894
1 200
TGE-100kN
0.1 N ~ 100 kN
600
1 350
860
(with CH/CHT-100kN)
1 221 x 2 192 x 720
900
TGE-50kN
0.1 N ~ 50 kN
420
1 015
480
(with CH/CHT-50kN)
900 x 1 522 x 490
200
±1 % of indicated value from 1/1 ~ 1/500 of load cell capacity = JIS 1 class (±0.5 % of indicated value = JIS 0.5 class is an option)
1 or 0.5 class of JIS B 7721, class 1 or 0.5 of ISO7500-1, Class 1 of ASTM E4
0.1, 0.5 and 1 ~ 500 (Possible to set by 1 mm/min pitch between this range)
High value either of ±0.5 % of the setting speed, or ±0.002 5 mm/min
Manual : Numeric input from control panel 0.1, 0.5, 1 ~ 500 mm/min (set by 1 mm/min pitch), PC : Automatically set by testing condition.
3 level speed (H/M/L), Each speed can be arbitrarily set. Single or cycle mode (Combination of testing power and position) Option : Creep, Automatic load.
5 ℃ ~ 40 ℃ / 20 % ~ 80 %RH (No condensing)
420 (with protect cover for lead screw)
1 100 (The maximum installation interval is 1 180)
660 x 1 619 x 503
80
Single phase AC100 V ~ 115 V, 50/60 Hz / 200 W Three phase AC200 V±20 V,
1.8 kW at maximum
Three phase AC200 V±20 V,
7.5 kW at maximum
Three phase AC200 V±20 V,
10 kW at maximum
Load cell capacity : Auto adjust, Load cell span : Auto set for tension / compression, Zero point : One push, Position reset : One push,
Operation detected sample rupture : Selectable from either stop, reverse or ignore, Rupture detectivity : arbitrary set with 0.1 % to 9.9 % of the
test force, Test condition registration : 10 condition, Analog output of test force and position : DC0 V to ±DC5 V (with scaling function),
Communication function : Conforming to USB interface 2.0/1.1 standard.
Test force: 5 digit display ±99 999, The peak and the rupture testing power can be displayed. Position: 5 digit and 1/2 ±1 999.99,
Accuracy: within 0.1 % of indicated value.
Tensile and Compression Testing Machine Tensile and Compression Testing Machine
? Applied OS：Windows XP , Windows Vista , Windows 7 (32 bit only)
? Memory：512 MB or more
? Communication function
1. Operating condition
2. Software
● Software for Standard testing
TgAnest (for TGI), SR-01-001 (for TG), SR-06-001(for TGE), SR-07-001(for LTS)
Corresponds to the test for tension, compression and bend (3 or 4 points)
An arbitrary formula and item name can be changed.
◆ Analytical item
Sectional area of specimen, Elastic modulus, Elasticity inclination (Spring constant)
Upper yield point, Lower yield point
Yield strength point,
The middle test force (6 points at max.)
The middle displacement point (6 points at max.)
The maximum test emphasis, Rupture point
An initial tensile resistance degree, the fineness, and the specific gravity can be
analyzed for the string examination.
Statistical work (50 or less in lot)
Ｒ
* Windows is the registered trade mark in the United States and other nations of Microsoft Corporation. Ｒ
● Analysis display
● Characteristics
◆
◆
◆
◆
Analyze the strength characteristics of various material and products
Supports report creation of ‘.txt’ and ‘.wmf’ files and graphs which can be inserted
into other applications.
Double graph screen supports a single graph and overlapping graphs while testing.
After the lot ends, the incremental test is possible.
The test force, the stress,
displacement, and the
strain have been calculated.
● Software for Adhesion test, Tear test and Friction test
TgAnest (for TGI), SR-01-002 (for TG), SR-06-002(for TGE), SR-07-002(for LTS)
Corresponds to the adhesion test for 90°, 135° and 180°, tear test and friction test
◆ Analytical item
Maximum local maximum point,
Minimum local minimum point,
The first maximum point,
The first local minimum point,
The middle displacement point
(six points or less), Rupture point,
Starting point of expansion,
Integration average,
Simple arithmetic average
Average of the maximum point,
Local minimum point average,
The maximum local minimum point average,
Tear test power,
Big and small, maximum point six point average
The middle displacement for 2, 3, 4, 5, and 6 points average
Average of collection
Internal tearing strength
Coefficient of dynamic friction, Coefficient of static friction
Energy, No. of the maximum points and the minimum points
Statistical work ((50 or less in lot)
● Software for other examinations
For rubber compression test (both appearance is possible)
For wood examination
For automatic load control examination
For spring examination
● Setting display of print format
Test force, conversion test force,
unit test force displacement,
and peel distance
Test force,
conversion test
force, and unit
test force
Data processing system
TG series D-sub 9 pin (Prepare the conversion connector for USB.)
TGI series / TGE series / LTS series USB 2.0/1.1 conforming.
● Pre-view of print format
● Display in the test process.
(Tension and compression test)
Mean value, Standard deviation, Standard deviation ×3, Minimum value of the maximum
value, Median, Maximum value - minimum value, Coefficient of variation, Mean value of
JIS K 6301, Sum total, Square of sum total, Number of N
Mean value, Standard deviation, Standard deviation ×3, Minimum value of the maximum
value, Median, Maximum value - minimum value, Coefficient of variation, Mean value of
JIS K 6301, Sum total, Square of sum total, Number of N
Ｒ Ｒ
