33
R
DRIVE, OPERATION, CEASING? 一、起動前準備:
二、起動:
三、運行:
四、停止:
1
2 ( 2mm
)?
3
( )?
4 ( )?
5
6
1 ( ) (?
) (?
) ( )?
3
2
3
1 ( 75 )?
( 1500 )?
2
3 30%
4
1 (?
)?
2
3
4
5
、起動前要把泵和現場清理干凈; 、檢查托架內潤滑油量是否適量 油量在油位計中心線 左
右 ,油位計是否完好; 、未接聯軸器前檢查原動機的轉向,與泵的轉向箭頭一致后
從電機端看,葉輪順時針旋轉 ,接好聯軸器; 、在裝好機械密封 或填料 和聯軸器后可輕便地用手轉動泵軸,
應無摩擦現象,并將聯軸器和防護罩安裝好; 、泵在有吸程情況下使用,起動前應灌泵或抽真空;泵在倒灌
情況下使用,起動前應用所輸送液將泵灌滿,驅除泵中的空氣后, 將吐出管的閘閥關閉; 、起動前檢查基礎螺栓有無松動,壓蓋是否歪斜,以及潤滑油
和冷卻水的供應情況;
、關閉進出口壓力 或真空 表和出水閥門、 如有旁通管,此時
也應關閉 起動電機 最好先點動、確認泵轉向正確后,才開始正式
運行 ,然后打開進出口壓力 或真空 計,當泵達到正常轉速,且儀
表指出相應壓力時,再慢慢打開出水閥門,調節至需要的工況。在
吐出管路關閉的情況下,泵連續工作時間,不能超過 分鐘; 、起動過程中要時時注意原動機的電流讀數及泵的振動情況; 、密封情況:機械密封應無泄漏、發熱現象,填料密封應呈連
續滴流狀態。
、經常檢查和電機的發熱情況 軸承的溫度不應超過 ℃ 及油
位計油面情況。 一般每運行 小時后,要全部更換潤滑油一次 ; 、不能用吸入閥來調節流量,避免產生汽蝕; 、泵不宜在低于 設計流量連續運轉,如果必須在該條件下
連續運轉,則應在出口外安裝旁通管,排除多余的流量; 、注意泵運轉有無雜音,發發現異常狀態時,應及時消除或停
車檢查。
、緩慢關閉吐出管路閘閥 如果泵在倒灌情況下使用,還要關
閉吸入管路的閘閥 ,并關閉各種儀表的開關; 、切斷電源; 、如果密封采用外部件引液時,還要關閉外引液閥門; 、如果環境溫度低于液體凝固時,要放凈泵內的液體,以防
凍裂; 、如果長時間停車不用,除將泵內的腐蝕性液體放凈外,各零
件應拆卸清洗干凈,尤其是密封腔,最好是將泵拆下清洗后重新裝
好,除涂油防銹處理和封閉泵進、出口外,還應定期檢查。
一
二
三
℃
四
.? 1. Please clean pump and working spor before driving?? 2. Check lubricant oil proper or not (oil surface is about central line 2mm on
oil meter) and oil meter perfect or not??
3. Before connect coupling should check the rotating direction of motor, the?
rotating direction should same as rotating direction of pump(looded from end of motor, impeller rotate as clockwise)??
4. After install mechanical seal(or packing) and coupling, it can easily manual?
rotate shaft of pump and with no attrition phenomenon, then install safe cover of
coupling?? 5. When pump use under condition of suction process, should irrigate pump
or deflate vacuum before drive, pump use under the condition of flow backward
should fill full of pump before drive, after get rid of the air in the pump, please shut? off the gate valve of dischange tube.? 6. Check foundation bolt loosen or not before drive, check stuffing gland whether crooked or not and supply status of lubricant oil and cooling water.?
.? 1. Shut off pressure meter on inlet and outlet (or vacuum) and outlet valve?
(any bypass tube should be shutted off either) drive motor (had better start in advance, confirm correct rotating direction to operate), then open outlet pressure? meter (vacuum), when pump reach to normal rotating speed and instrument to
corr esponding pressure, slowly open outlet valve and adjust to demanded working
status. Under the condition of dischange pipeline being shutted off, continuous? work time of pump can`t exceed 3 minutes?? 2. In process of operation it should pay attention to eletric currency digit of motor and vibration status of pump from time to time??
3. Sealing status: mechanical seal shouldn`t have leakage, heating phenomenon,? packing seal should be in continuous trickling stauts.?
.? 1. Constantly check heating circumstance of pump and motor (temperature of
bearing should`t exceed 75 ) and oil meter without oil surface status (generally,?
it should replace lubricant oil once after every 1500 hours)?? 2. Shouldn`t use suction valve to adjust capacity, prevent generating air erosion?? 3. Pump cannot operate continuously lower than 30% design capacity, if it has?
to operate under such condition, must install by pass pipe to get rid of unnecessary
capacity?? 4. Pay attention to the noise of operation of pump, if discover any abnormal?
state, please eliminate or stop operating timely.?
.? 1. Slow close dischange nozzle pipeline gate valve, and close switch on various?
instrument?? 2. Switch off electric power??
3. If seal utilize outside pilot liquid, need to close outside pilot liquid valve?? 4. If environmental temperature is lower than liquid freezing point, please? drain out liquid cleanly to prevent being splitted?? 5. If beposit if for a long time, please drain out corrosive liquid in pump clearly,?
disassemble and clean each part, especially the seal cavity. Had better reassemble?
it after cleaness, cover with anti-rust oil and block outlet and inlet of poum, besides,?
it should be inspected periodically.
Preparation berfore start:
Start:
Operation:
Stop: