06
08
10
07
09
工藝流程 Process flow
Production Process 生產流程
06
1. 拋光
這個過程分為兩部分，亞麻輪拋光和布輪拋光，亞麻輪拋光是粗
拋光，有效去除線面細小的橫紋、毛刺和輕微的機械紋；布輪拋
光，是一種精細的拋光工藝，是去除磨痕階段，保證線條表面光
滑，達到鏡面效果。
2. 噴砂
通過調整砂流清理的影響和粗化工藝的基本表面，采用不銹鋼德
國進口鋼砂，粒度均勻，保證線面油污，機械去粒干凈，啞面飽
和，高貴的質地。
3. 氧化
染色工藝對時間、溫度、染料濃度、墨粉質量和 pH 值有嚴格的
要求，會直接影響線條的色差。
表面處理Surface Treatment Color hole sealing
Cut and fold
Placing
Finished product packing
1. Polishing
This process is divided into two parts, linen wheel polishing
and cloth wheel polishing, linen wheel polishing is coarse
Polishing, effectively removing small horizontal lines, burrs and
slight mechanical lines on the line surface; cloth wheel polishing
Light is a fine polishing process. It is the stage of removing
the wear marks to ensure the smooth surface of the line.
Sliding to achieve a mirror effect.
2. Sandblasting
By adjusting the impact of sand flow cleaning and the basic
surface of the roughening process, stainless steel is used.
T h e s t e e l g r i t i m p o r t e d f r o m C h i n a h a s u n i f o r m
particle size, ensuring oil stains on the line surface,
clean mechanical de-graining, and full dumb surface
And, noble texture.
3. Oxidation
The dyeing process is strict with time, temperature,
dye concentration, toner quality and pH value
Requirements, will directly affect the color difference of the line.
07
08
09
10
染色后必須封線，封口分為常溫封口和中溫封口。 密封性決定了管線的耐候性。
取下鋁線，整齊排列在支架上晾干。線是氧化過程的產物，在生產過程中需要小
心處理。需要單個棉花分離器。
公司修邊人員用切割機對產品進行切割對應的長度，去除表面裝訂和左裝訂標記，
確保小裝訂產品整個切割的完整性和光滑度。
公司倉庫人員使用手推車、叉車進入成品倉庫，垂直和水平放入倉庫。
顏色封孔
放置
剪切和折疊
成品包裝
Lines must be closed after dyeing, The sealing is divided into normal
temperature sealing and medium temperature sealing. The sealing
determines the weatherability of the line .
Remove the aluminum lines and arrange them neatly on the support to air
dry. The lines are products of oxidation process, which need to be handled
with care during production. A single cotton separator is required.
The trimming staff of the company use the cutting machine to cut the
product to the corresponding length, remove the surface binding and left
binding marks, to ensure the integrity and smoothness of the entire cutting
of the small binding product.
warehouse personnel of the company use carts and forklifts to enter the
finished products warehouse, and put them into the warehouse vertically
and horizontally.
Quality in quality - Quantity in stars XINGON 8
