89151中世紀酒館燈光安裝教程

89151 Medieval tavern lighting installation tutorial

燈光材料如下

燈光組導線分布圖

1

2

3

4

5

6

7

8

9

10

注： 導 7 8 線的燈光組是兩節(jié)2燈

Lighting materials are as follows

Lighting group wire distribution diagram

Note: The light group of w 7 8 ires is two sections of 2 lights

1

2

3

4

拿出第一組燈光導線 1 2 3 4

來到酒館二層位置，將 導1 線的燈光組安裝如下

Take out the first set of light wires 1 2 3 4

Go to the second floor of the tavern and install the lighting

group of wire a 1 s follows

2

拿出 導2 線的燈光組

Take out the w 2 ire lighting group

將第三層頂部拆起

Remove the top of the third layer

將 導線上的燈光組如圖穿到頂部并安裝

在拆起的積木上

2

Thread the light group on the w 2 ires to the top and install

將積木安裝還原

拿出撬開器或者鑷子把積木拆起如下

Install and restore building blocks

Take out a pry or tweezers and remove the blocks as follows

把 導2 線穿過積木如下圖并將積木安裝還原

Pass wires through the building blocks as shown below

and install and restore the building blocks

2

拿出 導線的燈光組

4

3

3 4

Take out the w 3 4 ire light group

如圖，延箭頭方向?qū)艄饨M穿過

As shown, extend the arrow direction through the light group

將 導3 線的燈光組安裝如下

3

4

Install the light group of w 3 ires as follows

把 導線上的燈光組延箭頭方向穿到隔壁

4

4

將燈光組安裝如下

4

Thread the light group on wire in the direction of

the arrow to the next door

4

Install the light group as follows

拿出第二組燈光導線5 6 7 8

9

10

5

6

7

8

10

7

注： 導8 線的燈光組是兩節(jié)2燈

將所有燈光導線延箭頭方向穿過積木

9

Take out the second set of light wires 5 6 7 8 9 10

Note: The light group of w8 ires is two sections of 2 lights

7

Run all light wires through the blocks in the arrow direction

5

將 導5 線的燈光組安裝如下

6

6

剩下的燈光導線延箭頭方向穿過并安裝

導線的燈光組如圖

6

Install the light group of w 5 ires as follows

The remaining light wires pass through the arrow direction

and install the light group of w 6 ires as shown in the figure

7

8

9

10

剩下的燈光導線分布圖

7

8

拿出 導線的燈光組

7

8

The rest of the light wiring map

Take out the w 8 ire light group

7

延箭頭方向從旁邊穿過

再從第三層的上方箭頭位置穿下

Follow the arrow through the side

And then through the top arrow of the third layer

將導線拉到旁邊位置如箭頭所示

將三層的頂部拆起

Pull the wire to the side as indicated by the arrow

Remove the top of the three levels

7

8

把 導 7 8 線的燈光組安裝如下

將積木安裝還原

Install the light group of wire a 7 8 s follows

Install and restore building blocks

拿出 導線的燈光組如圖

9

9

10

10

如圖將二層的桌子拆起

Take out w 9 10 ire lighting group as shown

As shown in the picture, remove the table on the second floor

把 導 9 10 線和燈光組延箭頭方向穿過并還原桌子

將 導9 線的燈光組安裝在第一層如圖

9

10

Put the wires and lights through the arrow direction

and restore the table

9 10

Install the light group of w 9 ires on the first layer as shown

10

最后將 導10 線的燈光組延箭頭方向穿過

將最后一個燈光組安裝如下

Finally, the light group of the wire is extended through

the direction of the arrow

10

Install the last light group as follows

最后將電池盒裝入電池,USB接口連接到電池盒上

放置在下圖位置

Finally, install the battery box into the battery, connect

the USB interface to the battery box and place it in the

following position