第151頁
150 Subject to alterations
AERIAL FCC
2016.24.050.
EXPLODED VIEW
粉絲：{{bookData.followerCount}}
{{!bookData.isSubscribed?'關注':'取消關注'}}
懸吊斜楔(英）
Subject to alterations 151AERIAL FCC2016.24.050.PARTS LISTPosition Piece Designation Material spare part1 1 Slider GGG60 --2 1 Cam driver GGG60 --2.12.23 1 Cam base GGG60 --4.1 1 Clamp, left 1.7225 x4.2 1 Clamp, right 1.7225 x5.1 1 Positive return, left 1.7225 x5.2 1 Positive return, right 1.7225 x6 2 Sliding plate Bronze with solid lubricant x7 2 Sliding plate Bronze with solid lubricant x8 2 Sliding plate Bronze with solid lubricant x9* 2 Sliding plate Bronze with solid lubricant x10 2 Sliding...
粉絲: {{bookData.followerCount}}
文本內容
第152頁
Subject to alterations 151
AERIAL FCC
2016.24.050.
PARTS LIST
Position Piece Designation Material spare part
1 1 Slider GGG60 --
2 1 Cam driver GGG60 --
2.1
2.2
3 1 Cam base GGG60 --
4.1 1 Clamp, left 1.7225 x
4.2 1 Clamp, right 1.7225 x
5.1 1 Positive return, left 1.7225 x
5.2 1 Positive return, right 1.7225 x
6 2 Sliding plate Bronze with solid lubricant x
7 2 Sliding plate Bronze with solid lubricant x
8 2 Sliding plate Bronze with solid lubricant x
9* 2 Sliding plate Bronze with solid lubricant x
10 2 Sliding plate 1.7131 x
11 2 Sliding plate 1.7131 x
12
13 2 Gas spring 2487.12.03000.□□□ x
14 2 Stop plate 1.7225 x
15 2 Safety plate 1.1191 x
16.1 1 Cam slide stop, left 1.1191 x
16.2 1 Cam slide stop, right 1.1191 x
17
18 1 Lockout system x
19 4 Damping element Elastomer x
20 2 Feather key (T-nut) x
21 1 Feather key (T-nut) x
22
23* 1 Pre-acceleration x
24
* up to and including 45° with pre-acceleration
For inquiries or when ordering spare parts (x), we require the following data:
? Cam unit order no.
? Cam unit serial no.
? Item number / Designation / Spare part
第153頁
152 Subject to alterations
AERIAL FCC
2016.24.050.
SYSTEM AND SURROUNDING FORCES
Order number
a
[°]
FW
[kN]
FR*
[kN]
Fh2
[kN]
Fv2
[kN]
Fh3
[kN]
Fv3
[kN]
H2
[mm]
H3
[mm]
2016.24.050.00.2000.00 0 1155 108.4 0 969 1155 969 30 179
2016.24.050.05.2000.00 5 1155 109.0 84 965 1066 1066 40 172
2016.24.050.10.2000.00 10 1155 120.3 140 796 997 997 40 174
2016.24.050.15.2000.00 15 1155 120.9 209 781 906 1080 40 137
2016.24.050.20.2000.00 20 1155 121.4 277 760 809 1155 40 155
2016.24.050.25.2000.00 25 1155 125.0 282 604 765 1092 40 170
2016.24.050.30.2000.00 30 1155 125.0 333 578 667 1155 40 146
2016.24.050.35.2000.00 35 1155 125.0 309 441 637 1104 40 143
2016.24.050.40.2000.00 40 1155 125.0 346 413 539 1155 60 115
2016.24.050.45.2000.00 45 1155 125.0 297 297 519 1114 70 140
2016.24.050.50.2000.00 50 1155 125.0 322 270 420 1155 80 117
2016.24.050.55.2000.00 55 1155 125.0 254 178 409 1124 80 109
2016.24.050.60.2000.00 60 1155 125.0 268 155 309 1155 90 103
2016.24.050.65.2000.00 65 1155 125.0 185 86 304 1133 89 83
2016.24.050.70.2000.00 70 1155 125.0 95 35 300 1120 116 100
2016.24.050.75.2000.00 75 1155 125.0 98 26 201 1142 146 77
* Retraction force values correspond to the spring-generated retraction force at the working point
The forces Fh2, FV2 as well as Fh3, FV3 act on the tool environment at maximum working force FW.
第154頁
Subject to alterations 153
AERIAL FCC
2016.24.050.
FORCE DIAGRAM
shouldered
Width 500 mm
0° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 140 190 227 272 316 272 227 190 140
36 143 264 375 507 640 507 375 264 143
36 145 317 472 659 846 659 472 317 145
36 148 357 546 773 1000 773 546 357 148
36 151 397 620 887 1006 887 620 397 151
Support with feather key
Width 500 mm
0° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 63 82 109 160 210 160 109 82 63
36 64 82 110 161 212 161 110 82 64
36 64 82 110 163 214 163 110 82 64
36 66 82 110 173 237 173 110 82 66
36 68 82 110 173 237 173 110 82 68
Width 500 mm
5° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 138 210 268 333 398 333 268 210 138
36 146 268 378 511 643 511 378 268 146
36 154 325 480 667 853 667 480 325 154
36 159 366 553 779 1004 779 553 366 159
36 164 406 626 891 1155 891 626 406 164
Width 500 mm
5° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 64 88 116 173 230 173 116 88 64
36 65 88 116 175 233 175 116 88 65
36 66 88 116 177 235 177 116 88 66
36 68 88 116 180 245 180 116 88 68
36 69 88 116 180 245 180 116 88 69
Width 500 mm
10° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 137 209 274 353 431 353 274 209 137
36 150 271 381 541 646 541 381 271 150
36 163 334 489 675 861 675 489 334 163
36 170 375 561 784 1008 784 561 375 170
36 176 416 633 894 1155 894 633 416 176
Width 500 mm
10° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 64 88 112 186 250 186 112 88 64
36 66 88 112 189 253 189 112 88 66
36 68 88 112 192 256 192 112 88 68
36 69 88 112 198 265 198 112 88 69
36 71 88 112 204 274 204 112 88 71
Width 500 mm
15° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 135 207 272 351 430 351 272 207 135
36 153 275 385 517 649 517 385 275 153
36 172 342 497 683 868 683 497 342 172
36 180 384 568 790 1012 790 568 384 180
36 189 425 640 897 1155 897 640 425 189
Width 500 mm
15° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 65 89 117 200 270 200 117 89 65
36 68 89 117 203 273 203 117 89 68
36 70 89 117 206 277 206 117 89 70
36 71 89 117 208 279 208 117 89 71
36 73 89 117 210 281 210 117 89 73
Width 500 mm
20° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 143 214 280 358 436 358 280 214 143
36 157 278 389 521 653 521 389 278 157
36 172 342 498 684 870 684 498 342 172
36 170 376 563 788 1012 788 563 376 170
36 168 409 629 892 1155 892 629 409 168
Width 500 mm
20° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 72 93 128 189 250 189 128 93 72
36 74 93 130 192 253 192 130 93 74
36 76 93 133 194 256 194 133 93 76
36 77 93 135 197 260 197 135 93 77
36 79 93 137 201 264 201 137 93 79
Width 500 mm
25° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 150 222 287 365 443 365 287 222 150
36 161 282 393 525 657 525 393 282 161
36 172 343 498 685 872 685 498 343 172
36 159 368 558 786 1013 786 558 368 159
36 147 393 617 886 1155 886 617 393 147
Width 500 mm
25° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 79 97 126 178 230 178 126 97 79
36 80 97 128 180 233 180 128 97 80
36 82 97 130 183 235 183 130 97 82
36 83 97 133 187 241 187 133 97 83
36 85 97 136 192 248 192 136 97 85
第155頁
154 Subject to alterations
AERIAL FCC
2016.24.050.
FORCE DIAGRAM
shouldered
Width 500 mm
30° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 151 229 294 372 450 372 294 229 151
36 165 286 397 529 662 529 397 286 165
36 172 343 499 686 873 686 499 343 172
36 149 360 553 783 1014 783 553 360 149
36 126 378 606 881 1155 881 606 378 126
Support with feather key
Width 500 mm
30° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 86 105 125 167 210 167 125 105 86
36 86 105 126 169 212 169 126 105 86
36 86 105 128 171 214 171 128 105 86
36 86 105 161 177 223 177 161 105 86
36 86 105 135 183 231 183 135 105 86
Width 500 mm
35° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 144 219 287 369 450 369 287 219 144
36 161 284 396 530 665 530 396 284 161
36 178 349 505 692 880 692 505 349 178
36 166 374 563 790 1017 790 563 374 166
36 154 399 621 888 1155 888 621 399 154
Width 500 mm
35° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 82 93 111 180 266 180 111 93 82
36 85 101 127 220 288 220 127 101 85
36 86 101 133 235 310 235 133 101 86
36 86 101 135 241 318 241 135 101 86
36 86 101 135 248 325 248 135 101 86
Width 500 mm
40° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 131 209 280 365 450 365 280 209 131
36 157 282 396 532 668 532 396 282 157
36 183 355 511 699 886 699 511 355 183
36 183 387 574 797 1021 797 574 387 183
36 182 420 636 896 1155 896 636 420 182
Width 500 mm
40° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 90 92 113 175 322 175 113 92 90
36 92 101 125 221 364 221 125 101 92
36 94 110 145 237 406 237 145 110 94
36 94 110 145 280 413 280 145 110 94
36 94 110 145 280 419 280 145 110 94
Width 500 mm
45° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 118 199 273 362 442 362 273 199 118
36 154 280 395 533 671 533 395 280 154
36 186 361 517 705 893 705 517 361 186
36 200 401 584 804 1024 804 584 401 200
36 210 441 651 903 1155 903 651 441 210
Width 500 mm
45° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 92 127 182 222 378 222 182 127 92
36 95 129 203 283 440 283 203 129 95
36 100 131 224 313 502 313 224 131 100
36 100 131 224 313 508 313 224 131 100
36 100 131 224 313 513 313 224 131 100
Width 500 mm
50° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 122 201 272 349 420 349 272 201 122
36 148 279 399 542 685 542 399 279 148
36 174 358 525 726 927 726 525 358 174
36 183 393 584 812 1041 812 584 393 183
36 193 428 642 898 1155 898 642 428 193
Width 500 mm
50° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 93 105 129 187 363 187 129 105 93
36 103 125 153 207 486 207 153 125 103
36 105 137 169 296 609 296 169 137 105
36 107 140 173 325 617 325 173 140 107
36 107 140 173 325 625 325 173 140 107
Width 500 mm
55° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 126 202 259 328 397 328 259 202 126
36 143 279 402 550 699 550 402 279 143
36 160 356 534 747 961 747 534 356 160
36 167 385 583 820 1058 820 583 385 167
36 175 415 632 894 1155 894 632 415 175
Width 500 mm
55° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 105 113 132 187 347 187 132 113 105
36 107 132 160 263 531 263 160 132 107
36 122 150 185 315 630 315 185 150 122
36 127 156 185 339 659 339 185 156 127
36 132 156 185 339 659 339 185 156 132
第156頁
Subject to alterations 155
AERIAL FCC
2016.24.050.
FORCE DIAGRAM
shouldered
Width 500 mm
60° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 124 185 241 308 375 308 241 185 124
36 138 278 406 559 712 559 406 278 138
36 145 353 542 768 995 768 542 353 145
36 151 377 582 829 1075 829 582 377 151
36 158 401 623 889 1155 889 623 401 158
Support with feather key
Width 500 mm
60° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 105 111 131 170 332 170 131 111 105
36 109 126 150 225 483 225 150 126 109
36 120 157 208 298 822 298 208 157 120
36 138 180 227 420 835 420 227 180 138
36 140 180 227 420 849 420 227 180 140
Width 500 mm
65° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 128 186 238 301 363 301 238 186 128
36 147 290 413 560 707 560 413 290 147
36 167 363 542 756 970 756 542 363 167
36 181 397 592 828 1063 828 592 397 181
36 195 430 643 899 1155 899 643 430 195
Width 500 mm
65° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 123 126 151 169 260 169 151 126 123
36 127 147 173 228 502 228 173 147 127
36 153 193 221 279 750 279 221 193 153
36 165 201 268 449 880 449 268 201 165
36 177 207 268 473 880 473 268 207 177
Width 500 mm
70° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 132 186 235 293 352 293 235 186 132
36 146 271 385 521 658 521 385 271 146
36 161 357 536 744 946 744 536 357 161
36 209 416 603 827 1051 827 603 416 209
36 233 458 663 909 1155 909 663 458 233
Width 500 mm
70° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 125 150 181 227 240 227 181 150 125
36 143 175 207 263 500 263 207 175 143
36 160 223 245 325 753 325 245 223 160
36 193 245 360 521 890 521 360 245 193
36 215 245 390 553 890 553 390 245 215
Width 500 mm
75° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 136 186 231 286 340 286 231 186 136
36 145 253 351 468 585 468 351 253 145
36 155 320 470 651 831 651 470 320 155
36 202 400 579 794 1009 794 579 400 202
36 250 479 683 919 1155 919 683 479 250
Width 500 mm
75° 50 50 60 60 60 60 60 50 50
Height
180 mm
36 126 157 220 230 290 230 220 157 126
36 141 175 220 260 557 260 220 175 141
36 155 278 419 551 831 551 419 278 155
36 202 303 478 691 1038 691 478 303 202
36 250 325 536 702 1155 702 536 325 250
第157頁
156 Subject to alterations
第158頁
157
AERIAL FCC
2016.24.060.
Working width: 600 mm
Performance class: 1200 kN
第159頁
158 Subject to alterations
AERIAL FCC
2016.24.060.
SIZE TABLE
第160頁
Subject to alterations 159
AERIAL FCC
2016.24.060.
SIZE TABLE
Order number
2016.24.060.
L
[mm]
B
[mm]
H
[mm]
H1
[mm]
HW
[mm]
L1
[mm]
L2
[mm]
L3
[mm]
L4
[mm]
L5
[mm]
D
[mm]
a
[°]
b
[°]
δ
[°]
SW*
[mm]
SWA*
[mm]
SS
[mm]
SP*
[mm]
SPA*
[mm]
00.2000.00 388 600 400 185 200 380 385 260 255 110 368.0 0 50 45 - 25.0 58 - 56.7
05.2000.00 385 600 400 200 200 380 385 275 258 110 384.0 5 45 50 - 25.0 58 - 62.3
10.2000.00 387 600 400 210 200 380 385 275 245 110 398.7 10 45 45 - 25.0 58 - 61.8
15.2000.00 397 600 400 220 200 380 385 285 245 110 412.0 15 40 50 - 35.0 58 - 59.0
20.2000.00 391 600 400 230 200 365 380 310 260 110 409.7 20 35 45 - 35.0 58 - 59.9
25.2000.00 401 600 400 240 200 365 380 310 250 110 420.2 25 35 50 - 35.0 58 - 66.8
30.2000.00 410 600 400 240 200 365 400 320 250 110 424.1 30 30 45 - 35.0 58 - 66.4
35.2000.00 418 600 400 250 200 365 415 360 280 110 430.4 35 30 50 - 40.0 58 - 72.8
40.2000.00 435 600 400 260 200 365 435 360 275 110 434.7 40 25 55 - 50.0 58 - 77.0
45.2000.00 435 600 400 270 200 365 435 360 265 110 437.0 45 25 60 - 55.0 58 - 87.1
50.2000.00 460 600 400 280 200 320 455 325 225 140 408.1 50 20 - 84.8 - 58 84.8 -
55.2000.00 460 600 400 290 200 320 455 325 215 140 409.1 55 20 - 95.0 - 58 97.7 -
60.2000.00 470 600 400 305 200 310 455 325 215 140 407.1 60 15 - 112.0 - 58 112.0 -
65.2000.00 495 600 400 315 200 310 495 305 185 140 404.5 65 15 - 102.9 - 45 104.9 -
70.2000.00 495 600 400 330 200 310 495 305 180 140 404.1 70 15 - 127.1 - 45 131.1 -
75.2000.00 495 600 400 340 200 310 495 305 175 140 396.6 75 10 - 114.2 - 30 115.5 -
* Values rounded
Fastening cam base:
Hexagon socket head cap screws DIN EN ISO 4762 8x M20 / Strength class min. 8.8
Dowel pins DIN EN ISO 8735 2x ?20
Fastening cam driver :
Hexagon socket head cap screws DIN EN ISO 4762 8x M16 / Strength class min. 8.8
Dowel pins DIN EN ISO 8735 4x ?16
第161頁
160 Subject to alterations
AERIAL FCC
2016.24.060.
EXPLODED VIEW
第162頁
Subject to alterations 161
AERIAL FCC
2016.24.060.
PARTS LIST
Position Piece Designation Material spare part
1 1 Slider GGG60 --
2
2.1 1 Cam driver, left GGG60 --
2.2 1 Cam driver, right GGG60 --
3 1 Cam base GGG60 --
4.1 1 Clamp, left 1.7225 x
4.2 1 Clamp, right 1.7225 x
5.1 1 Positive return, left 1.7225 x
5.2 1 Positive return, right 1.7225 x
6 4 Sliding plate Bronze with solid lubricant x
7 2 Sliding plate Bronze with solid lubricant x
8 2 Sliding plate Bronze with solid lubricant x
9* 2 Sliding plate Bronze with solid lubricant x
10 4 Sliding plate 1.7131 x
11 2 Sliding plate 1.7131 x
12 2 Sliding plate 1.7131 x
13 2 Gas spring 2487.12.03000.□□□ x
14 2 Stop plate 1.7225 x
15 2 Safety plate 1.1191 x
16.1 1 Cam slide stop, left 1.1191 x
16.2 1 Cam slide stop, right 1.1191 x
17 1 Spacer 1.1191 x
18 1 Lockout system x
19 4 Damping element Elastomer x
20 3 Feather key (T-nut) x
21
22 2 Feather key (T-nut) x
23* 2 Pre-acceleration x
24
* up to and including 45° with pre-acceleration
For inquiries or when ordering spare parts (x), we require the following data:
? Cam unit order no.
? Cam unit serial no.
? Item number / Designation / Spare part
第163頁
162 Subject to alterations
AERIAL FCC
2016.24.060.
SYSTEM AND SURROUNDING FORCES
Order number
a
[°]
FW
[kN]
FR*
[kN]
Fh2
[kN]
Fv2
[kN]
Fh3
[kN]
Fv3
[kN]
H2
[mm]
H3
[mm]
2016.24.060.00.2000.00 0 1202 108.8 0 1009 1202 1009 40 220
2016.24.060.05.2000.00 5 1202 109.4 88 1005 1110 1110 40 210
2016.24.060.10.2000.00 10 1202 120.7 146 829 1038 1038 40 210
2016.24.060.15.2000.00 15 1202 121.3 218 813 943 1124 40 193
2016.24.060.20.2000.00 20 1202 121.7 288 791 842 1202 40 180
2016.24.060.25.2000.00 25 1202 125.0 293 629 796 1137 40 180
2016.24.060.30.2000.00 30 1202 125.0 347 601 694 1202 40 145
2016.24.060.35.2000.00 35 1202 125.0 321 459 663 1149 45 145
2016.24.060.40.2000.00 40 1202 125.0 360 429 561 1202 65 101
2016.24.060.45.2000.00 45 1202 125.0 309 309 541 1159 90 64
2016.24.060.50.2000.00 50 1202 125.0 335 281 437 1202 120 58
2016.24.060.55.2000.00 55 1202 125.0 264 185 426 1169 120 80
2016.24.060.60.2000.00 60 1202 125.0 279 161 322 1202 130 92
2016.24.060.65.2000.00 65 1202 125.0 192 90 316 1179 140 82
2016.24.060.70.2000.00 70 1202 125.0 99 36 312 1165 140 73
2016.24.060.75.2000.00 75 1202 125.0 102 27 210 1188 150 66
* Retraction force values correspond to the spring-generated retraction force at the working point
The forces Fh2, FV2 as well as Fh3, FV3 act on the tool environment at maximum working force FW.
第164頁
Subject to alterations 163
AERIAL FCC
2016.24.060.
FORCE DIAGRAM
shouldered
Width 600 mm
0° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 90 216 302 385 473 385 302 216 90
40 98 240 374 494 619 494 374 240 98
40 107 265 422 586 756 586 422 265 107
40 117 351 554 765 983 765 554 351 117
40 126 406 662 927 1202 927 662 406 126
Support with feather key
Width 600 mm
0° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 45 63 68 93 118 93 68 63 45
40 48 63 70 93 118 93 70 63 48
40 51 63 70 93 118 93 70 63 51
40 52 63 70 93 118 93 70 63 52
40 53 63 70 93 118 93 70 63 53
Width 600 mm
5° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 92 219 299 382 469 382 299 219 92
40 101 262 378 498 623 498 378 262 101
40 110 306 457 615 778 615 457 306 110
40 121 361 563 772 990 772 563 361 121
40 131 416 668 930 1202 930 668 416 131
Width 600 mm
5° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 47 68 75 105 136 105 75 68 47
40 49 68 79 105 136 105 79 68 49
40 51 68 79 105 136 105 79 68 51
40 52 68 79 105 136 105 79 68 52
40 53 68 79 105 136 105 79 68 53
Width 600 mm
10° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 95 216 296 379 465 379 296 216 95
40 104 266 382 503 628 503 382 266 104
40 114 315 468 626 791 626 468 315 114
40 125 371 571 780 996 780 571 371 125
40 135 426 675 933 1202 933 675 426 135
Width 600 mm
10° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 48 74 82 117 154 117 82 74 48
40 50 74 95 117 154 117 95 74 50
40 51 74 95 117 154 117 95 74 51
40 52 74 95 117 154 117 95 74 52
40 53 74 95 117 154 117 95 74 53
Width 600 mm
15° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 97 214 293 376 461 376 293 214 97
40 107 270 386 507 632 507 386 270 107
40 117 325 479 638 803 638 479 325 117
40 129 380 580 787 1002 787 580 380 129
40 140 435 681 937 1202 937 681 435 140
Width 600 mm
15° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 50 79 89 130 172 130 89 79 50
40 50 79 99 130 172 130 99 79 50
40 51 79 109 130 172 130 109 79 51
40 52 79 109 130 172 130 109 79 52
40 53 79 109 130 172 130 109 79 53
Width 600 mm
20° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 95 219 295 375 457 375 295 219 95
40 106 275 392 514 641 514 392 275 106
40 118 331 489 654 825 654 489 331 118
40 131 375 580 793 1013 793 580 375 131
40 145 419 670 931 1202 931 670 419 145
Width 600 mm
20° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 51 85 96 143 191 143 96 85 51
40 53 85 110 143 191 143 110 85 53
40 55 85 110 143 191 143 110 85 55
40 58 85 110 143 191 143 110 85 58
40 60 85 110 143 191 143 110 85 60
Width 600 mm
25° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 93 215 298 374 454 374 298 215 93
40 106 280 399 522 650 522 399 280 106
40 119 336 500 670 847 670 500 336 119
40 134 370 580 798 1024 798 580 370 134
40 147 403 660 926 1202 926 660 403 147
Width 600 mm
25° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 53 91 103 156 211 156 103 91 53
40 56 91 112 156 211 156 112 91 56
40 59 91 112 156 211 156 112 91 59
40 63 91 112 156 211 156 112 91 63
40 68 91 112 156 211 156 112 91 68
第165頁
164 Subject to alterations
AERIAL FCC
2016.24.060.
FORCE DIAGRAM
shouldered
Width 600 mm
30° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 90 207 300 373 450 373 300 207 90
40 105 285 405 530 659 530 405 285 105
40 119 341 510 686 868 686 510 341 119
40 137 364 580 803 1035 803 580 364 137
40 126 387 649 920 1202 920 649 387 126
Support with feather key
Width 600 mm
30° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 54 97 111 169 230 169 111 97 54
40 59 97 130 185 283 185 130 97 59
40 63 97 130 185 283 185 130 97 63
40 69 97 130 185 283 185 130 97 69
40 76 97 130 185 283 185 130 97 76
Width 600 mm
35° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 94 205 313 388 466 388 313 205 94
40 105 294 415 541 671 541 415 294 105
40 117 347 517 694 876 694 517 347 117
40 140 378 590 811 1039 811 590 378 140
40 154 409 663 928 1202 928 663 409 154
Width 600 mm
35° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 61 98 125 190 259 190 125 98 61
40 67 98 132 220 300 220 132 98 67
40 74 98 132 220 300 220 132 98 74
40 74 98 132 220 300 220 132 98 74
40 74 98 132 220 300 220 132 98 74
Width 600 mm
40° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 97 202 306 402 482 402 306 202 97
40 106 303 425 552 683 552 425 303 106
40 114 354 524 701 884 701 524 354 114
40 144 392 601 818 1043 818 601 392 144
40 174 430 678 935 1202 935 678 430 174
Width 600 mm
40° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 67 101 139 211 287 211 139 101 67
40 67 101 141 211 318 211 141 101 67
40 67 101 141 211 350 211 141 101 67
40 67 101 141 211 350 211 141 101 67
40 67 101 141 211 350 211 141 101 67
Width 600 mm
45° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 101 199 297 399 497 399 297 199 101
40 106 307 435 563 695 563 435 307 106
40 111 360 531 708 893 708 531 360 111
40 147 405 611 825 1047 825 611 405 147
40 183 451 692 942 1202 942 692 451 183
Width 600 mm
45° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 67 108 152 186 315 186 152 108 67
40 67 108 153 196 336 196 153 108 67
40 67 108 153 240 357 240 153 108 67
40 67 108 153 240 357 240 153 108 67
40 67 108 153 240 357 240 153 108 67
Width 600 mm
50° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 92 184 276 372 471 372 276 184 92
40 100 282 452 594 740 594 452 282 100
40 109 380 563 754 952 754 563 380 109
40 142 415 628 848 1077 848 628 415 142
40 176 451 692 942 1202 942 692 451 176
Width 600 mm
50° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 65 145 164 242 323 242 164 145 65
40 65 164 168 275 370 275 168 164 65
40 65 176 168 309 417 309 168 176 65
40 65 176 168 309 445 309 168 176 65
40 65 176 168 309 445 309 168 176 65
Width 600 mm
55° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 83 169 256 345 438 345 256 169 83
40 95 257 420 589 764 589 420 257 95
40 106 345 584 800 1012 800 584 345 106
40 138 425 644 871 1107 871 644 425 138
40 169 451 692 942 1202 942 692 451 169
Width 600 mm
55° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 67 115 175 211 330 211 175 115 67
40 67 115 196 302 403 302 196 115 67
40 67 115 196 316 466 316 196 115 67
40 67 115 196 316 466 316 196 115 67
40 67 115 196 316 466 316 196 115 67
第166頁
Subject to alterations 165
AERIAL FCC
2016.24.060.
FORCE DIAGRAM
shouldered
Width 600 mm
60° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 74 155 235 318 404 318 235 155 74
40 89 232 376 525 679 525 376 232 89
40 104 310 517 731 954 731 517 310 104
40 133 414 660 894 1136 894 660 414 133
40 163 451 692 942 1202 942 692 451 163
Support with feather key
Width 600 mm
60° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 74 128 186 240 338 240 186 128 74
40 74 128 223 265 437 265 223 128 74
40 74 128 223 378 536 378 223 128 74
40 74 128 223 380 614 380 223 128 74
40 74 128 223 380 614 380 223 128 74
Width 600 mm
65° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 71 153 235 319 408 319 235 153 71
40 86 231 376 527 684 527 376 231 86
40 100 309 518 736 961 736 518 309 100
40 122 397 671 913 1156 913 671 397 122
40 145 466 702 947 1202 947 702 466 145
Width 600 mm
65° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 71 133 203 291 383 291 203 133 71
40 77 133 251 383 519 383 251 133 77
40 77 133 251 392 643 392 251 133 77
40 77 133 251 392 643 392 251 133 77
40 77 133 251 392 643 392 251 133 77
Width 600 mm
70° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 68 151 234 321 411 321 234 151 68
40 82 230 377 530 689 530 377 230 82
40 96 308 520 740 968 740 520 308 96
40 112 380 648 926 1176 926 648 380 112
40 127 451 713 953 1202 953 713 451 127
Width 600 mm
70° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 67 151 220 321 411 321 220 151 67
40 82 173 280 437 601 437 280 173 82
40 96 175 280 439 640 439 280 175 96
40 124 178 280 439 640 439 280 178 124
40 124 178 280 439 640 439 280 178 124
Width 600 mm
75° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 64 149 234 322 414 322 234 149 64
40 79 228 378 533 694 533 378 228 79
40 93 307 522 744 975 744 522 307 93
40 101 363 624 896 1178 896 624 363 101
40 110 419 723 958 1202 958 723 419 110
Width 600 mm
75° 65 65 65 70 70 70 65 65 65
Height
200 mm
40 64 149 234 273 414 273 234 149 64
40 79 149 308 350 578 350 308 149 79
40 93 149 378 513 743 513 378 149 93
40 104 149 372 548 862 548 372 149 104
40 104 149 366 548 832 548 366 149 104
第167頁
166 Subject to alterations
AERIAL FCC
2016.24.006./.008./.011.
ASSEMBLY INSTRUCTIONS
Step 1
? Remove screws (1+2)
? Remove stop plate (3) of the
gas spring
? Remove spacer (4) and gas
spring (5) from the bore
CAUTION
The gas spring may only be
removed if the spring is released.
After removing the stop plate for the
gas spring, observe that there is a
risk of crushing between the cam
unit driver and the cam unit base
due to independent movement of
the cam unit driver.
Step 2
? Slide the cam unit driver into the
front position
CAUTION
Risk of crushing between the cam
unit driver and the cam unit base by
movement of the cam unit driver.
Step 3
? Insert the lockout sleeve (6)
? Secure the cam unit driver with
the screw (7)
This position corresponds to the
closed position (working position) in
the tool.
CAUTION
In the classic tool setup process
(pressing the cam driver in the die),
the positive return left (9) and right
(8) must additionally be removed
in order to avoid damaging the cam
unit, cam driver and die.
第168頁
Subject to alterations 167
AERIAL FCC
2016.24.006./.008./.011.
ASSEMBLY INSTRUCTIONS
Step 4
Restore the cam unit function after
completion of the work (setup, work
surface machining).
? Remove screw (7)
? Remove the lockout sleeve (6)
Step 5
? Slide the cam unit driver
backwards
CAUTION
Risk of crushing between the cam
unit driver and the cam unit base by
movement of the cam unit driver.
Step 6
? Insert gas spring (5) and spacer
(4)
? Insert stop plate (3) for gas
spring and secure with screws
(2+1)
Screws must be secured against
loosening by means of adhesive or
suitable lock washers.
第169頁
168 Subject to alterations
AERIAL FCC
2016.24.015./.018./.022./.026./.033./.040./.050.
ASSEMBLY INSTRUCTIONS
Step 1
? Remove screws (1 + 2)
? Remove lock washer (3)
(from cam unit width 220m)
? Remove the stop plate (4) of the
gas spring
? Remove spacer (5) only up to
cam unit width 260 mm) and gas
spring (6) from the bore
CAUTION
The gas spring may only be
removed if the spring is released.
After removing the stop plate for the
gas spring, observe that there is a
risk of crushing between the cam
unit driver, stop, and cam unit base
due to independent movement of
the cam unit driver.
Step 2
? Slide the cam unit driver into the
front position
CAUTION
Risk of crushing between the cam
unit driver, stop, and cam unit base
by movement of the cam unit driver.
Step 3
? Insert lockout system (7) and fix
with screws (8)
? Insert the spacer (not shown)
between the lockout and the cam
unit driver (cam unit width 110
and 150 mm)
? Fix the cam unit driver with the
screws (9)
This position corresponds to the
closed position (working position) in
the die.
CAUTION
In the classic tool setup process
(pressing the cam driver in the die),
the positive return right (10) and left
(11) must be removed in order to
avoid damaging the cam unit, cam
driver and die.
第170頁
Subject to alterations 169
AERIAL FCC
2016.24.015./.018./.022./.026./.033./.040./.050.
ASSEMBLY INSTRUCTIONS
Step 4
Restore the cam unit function after
completion of the work (setup, work
surface machining).
? Remove screws (9)
? Remove spacer (not shown)
(cam unit width 110 and150 mm)
? Loosen the screws (8) and
remove the lockout system (7)
Step 5
? Slide the cam unit driver
backwards
CAUTION
Risk of crushing between the cam
unit driver, stop, and cam unit base
by movement of the cam unit driver.
Step 6
? Insert the gas spring (6) and the
spacer (5) (only up to the slide
width 260 mm)
? Insert the stop plate (4) for the
gas spring
? Insert lock washer (3) (from cam
unit width 220m)
? Fix stop plate and lock washer
with screws (2 + 1)
Screws must be secured against
loosening by means of adhesive or
suitable lock washers.
第171頁
170 Subject to alterations
AERIAL FCC
2016.24.060.
ASSEMBLY INSTRUCTIONS
Step 1
? Insert the spacer (1) and secure
with screws (not shown)
? Remove screws (2 + 3)
? Remove lock washers (4)
? Remove the stop plates (5) of the
gas springs
? Remove the gas springs (6) from
the bore
CAUTION
The gas spring may only be
removed if the spring is released.
After removing the stop plate for the
gas spring, observe that there is a
risk of crushing between the cam
unit driver, stop, and cam unit base
due to independent movement of
the cam unit driver.
Step 2
? Slide the cam unit driver into the
front position
CAUTION
Risk of crushing between the cam
unit driver, stop, and cam unit base
by movement of the cam unit driver.
Step 3
? Fix cam unit driver with lockout
screw (7) in the front position
This position corresponds to the
closed position (working position) in
the tool.
CAUTION
In the classic tool setup process
(pressing the cam driver in the
tool), the positive return right (8)
and left (9) must be removed in
order to avoid damaging the cam
unit, cam driver and tool.
第172頁
Subject to alterations 171
AERIAL FCC
2016.24.060.
ASSEMBLY INSTRUCTIONS
Step 4
Restore the cam unit function after
completion of the work (setup, work
surface machining).
? Remove lockout screws (7)
Step 5
? Slide the cam unit driver
backwards
CAUTION
Risk of crushing between the cam
unit driver, stop, and cam unit base
by movement of the cam unit driver.
Step 6
? Insert gas springs (6) in bores
? Insert the stop plates (5) for the
gas springs
? Insert lock washers (4)
? Fix stop plate and lock washer
with screws (3 + 2)
? Remove spacer (1)
Screws must be secured against
loosening by means of adhesive or
suitable lock washers.
第173頁
172 Subject to alterations
AERIAL FCC
2016.24.
ASSEMBLY IN THE TOOL
Series 2016.24. cam units are designed so that the screws and pins for positioning and securing the cam unit
components in the die are accessible in the open position of the cam unit.
This accessibility can be restricted or completely prevented by tooling on the cam unit working surface.
In such cases, the disassembly / assembly of the fitted cam unit is possible by disassembling the clamp:
Step 1
? Remove the gas spring before
disassembling the cam unit.
In the die, the corresponding
mechanical clearances must be
taken into account backwards.
CAUTION
The gas spring may only be
removed if the spring is released.
After removing the stop plate for the
gas spring, observe that there is a
risk of crushing between the cam
unit driver and the cam unit base
due to independent movement of
the cam unit driver.
Step 2
? Loosen and remove the left and
right guide clamps. No removal of
positioning pins required!
In the die, the corresponding
mechanical clearances must be
provided at the sides.
第174頁
Subject to alterations 173
AERIAL FCC
2016.24.
ASSEMBLY IN THE TOOL
Step 3
? Lift the (equipped) cam unit
upwards.
The cam unit base can remain in
the upper die
In the case of installation space
problems in the die, an additional
mounting plate can also be used
as an alternative. The cam unit
is positioned and fixed on this
mounting plate, the positioning
and fastening possibilities to the
die lie outside the compact cam
unit structure, and are thus easily
accessible from above for the
necessary fitting aids.
Mounting plates are to be provided
by the tool shop if necessary, they
are not included in the delivery
scope of FIBRO cam units.
第175頁
174 Subject to alterations
第176頁
INTRODUCTION
AND TABLE OF CONTENTS
ENGINEERING
2016.24. AERIAL FCC BAK DAIMLER, VOLVO,
VOLKSWAGEN?GROUP
2016.25. AERIAL FCC BAK DAIMLER, VOLVO,
VOLKSWAGEN?GROUP
2016.207. AERIAL ECO LINE
2016.208. AERIAL ECO LINE
CUSTOMER-SPECIFIC
SERVICES
APPENDIX
EMERGENCY SITUATION /
CONTACTS
第177頁
176
AERIAL FCC
2016.25.
第178頁
Subject to alterations 177
AERIAL FCC
2016.25.
FIBRO FCC cam units series 2016.25. are a continuation of the FCC Series from a width of 700?mm and higher.
This series also impresses with its excellent load bearing as well as the highest precision even after a high number
of pressing.
All sliding elements of the cam unit correspond to the VDI standard. The sliding elements are shouldered to absorb
thrust. The return springs are accessible from the back side of the cam unit, so that they can be dismounted from
the die without removing the cam unit.
FIBRO FCC cam units series 2016.25. meet the requirements of the BAK product specifications.
Various ordering options are available for FIBRO FCC cam units series 2016.25.
? The working surface can be optionally equipped with or without shoulder
? Up to an angle of 45°, the cam units are equipped with a pre-acceleration, whereby a choice can be made
between roll or plate pre-acceleration.
FIBRO cam units series 2016.25. are machined on the outer surfaces of the back side of the working surface. This
makes it possible to machine the working surface of the cam unit with a simple clamping.
FIBRO FCC cam units series 2016.25. are, of course, available ex works, manufactured according to customer
requirements. This meets the highest requirements of modern tool and die makers.
Design features:
? Double prismatic guide against cam driver, square positioned guiding elements against cam base.
? Sliding surfaces hardened steel / bronze with solid lubricant
? Gas springs
? Positive locking connections
FIBRO FCC cam units series 2016.25. are available in the widths from 700 to 1050?mm and in the angular
variants 0°?to?75?° (gradation 5°).
Order number Width [mm] Performance class [kN]* Page
2016.25.070.□□.□000.02 700 1600 179
2016.25.075.□□.□000.02 750 1600 179
2016.25.080.□□.□000.02 800 1700 189
2016.25.085.□□.□000.02 850 1700 189
2016.25.090.□□.□000.02 900 1800 199
2016.25.095.□□.□000.02 950 1800 199
2016.25.100.□□.□000.02 1000 2000 209
2016.25.105.□□.□000.02 1050 2000 209
* For exact power values, please refer to the force diagrams of the corresponding cam units
Order options:
.1000 Working surface standard, roll pre-acceleration
.2000 Working surface offset (shoulder on working surface), roll pre-acceleration
.3000 Working surface standard, plate pre-acceleration
.4000 Working surface offset (shoulder on working surface), plate pre-acceleration
Ordering example:
FIBRO cam unit FCC, aerial, width 850 mm = 2016.25.085.□□.□000.02
Cam unit angle a = 35° = 35.
Working surface offset (shoulder on working surface), plate pre-acceleration = 4000.
Order number = 2016.25.085. 35. 4000.02
第179頁
178 Subject to alterations
第180頁
179
AERIAL FCC
2016.25.070./.075.
Working width: 700/750 mm
Performance class: 1600 kN
第181頁
180 Subject to alterations
AERIAL FCC
2016.25.070./.075.
SIZE TABLE
第182頁
Subject to alterations 181
AERIAL FCC
2016.25.070./.075.
SIZE TABLE
Order No.
2016.25.7□0.
L**
[mm]
B***
[mm]
H
[mm]
H1
[mm]
HW
[mm]
L1
[mm]
L2
[mm]
L3
[mm]
L4
[mm]
L5
[mm]
D*
[mm]
a
[°]
b
[°]
δ
[°]
SW*
[mm]
SWA*
[mm]
SS
[mm]
SP*
[mm]
SPA*
[mm]
00.□000.02 395 7□0 400 208 220 365 370 280 305 80 395 0 50 45 - 45.7 100 - 95.2
05.□000.02 409.1 7□0 400 209 220 367.03 385 297.03 308 80 413.8 5 45 50 - 53.8 100 - 95.8
10.□000.02 428 7□0 400 208.61 220 374.12 385 304.12 302 80 434.7 10 45 45 - 56.6 100 - 95.5
15.□000.02 441.4 7□0 400 218.84 220 376.22 405 316.22 300 80 450 15 40 50 - 65.5 100 - 97.2
20.□000.02 449.3 7□0 400 229.69 220 373.27 410 298.27 270 80 459.3 20 40 45 - 68.8 100 - 99.8
25.□000.02 456.6 7□0 400 236.16 220 370.22 420 305.22 263 80 465.3 25 35 50 - 74.3 95 - 98.4
30.□000.02 458 7□0 400 243.22 220 362.01 425 312.01 258 80 465.1 30 35 45 - 79.5 95 - 103.2
35.□000.02 458.5 7□0 400 250.86 220 353.6 440 318.6 253 80 463.5 35 30 50 - 81.4 85 - 97.5
40.□000.02 462.9 7□0 400 259.08 220 349.93 450 324.93 247 80 464.6 40 25 55 - 93.0 85 - 104.0
45.□000.02 461.2 7□0 400 262.83 220 340.96 455 330.96 243 80 456.9 45 20 60 - 100.2 80 - 105.7
50.□000.02 483.2 7□0 400 267.09 220 356.64 480 336.64 264 80 463.9 50 10 - 107.2 - 70 94.3 -
55.□000.02 475.1 7□0 400 271.83 220 331.93 460 341.93 260 80 443.1 55 10 - 103.0 - 60 94.8 -
60.□000.02 480 7□0 400 277.01 220 316.78 470 326.78 237 80 428.3 60 10 - 108.3 - 55 103.4 -
65.□000.02 490 7□0 400 282.6 220 281.17 440 331.17 234 80 404.9 65 0 - 106.5 - 45 96.5 -
70.□000.02 505 7□0 400 288.54 220 265.05 435 335.05 232 80 391.8 70 0 - 117.0 - 40 109.9 -
75.□000.02 515 7□0 400 294.81 220 248.39 425 338.39 230 80 379.1 75 0 - 115.9 - 30 112.0 -
* Values rounded
** Values L, D measured for option with shouldered working surface
*** 7□0 = 700 or 750 mm
Mounting cam base:
Hexagon socket head cap screws DIN EN ISO 4762 8x M20 / Strength class min. 8.8
Dowel pins DIN EN ISO 8735 2x ?16
Mounting cam driver:
Hexagon socket head cap screws DIN EN ISO 4762 2x4 M16 / Strength class min. 8.8
Dowel pins DIN EN ISO 8735 2x2 ?12
第183頁
182 Subject to alterations
AERIAL FCC
2016.25.070./.075.
EXPLODED VIEW
第184頁
Subject to alterations 183
AERIAL FCC
2016.25.070./.075.
PARTS LIST
Position Piece Designation Material spare part
1 1 Slider
2.1 1 Driver, left
2.2 1 Driver, right
3 1 Slider base
4.1 1 Clamp, left x
4.2 1 Clamp, right x
5.1 1 Positive return, left x
5.2 1 Positive return, right x
6 4 Sliding plate VDI Bronze with solid lubricant x
7 2 Sliding plate VDI Bronze with solid lubricant x
8 2 Sliding plate VDI Bronze with solid lubricant x
9 2 Sliding plate VDI Bronze with solid lubricant x
10 2 Sliding plate VDI Bronze with solid lubricant x
11 2 Sliding plate VDI Bronze with solid lubricant x
12** 2 Sliding plate VDI Bronze with solid lubricant x
13 2 Sliding plate VDI Steel x
14 2 Sliding plate VDI Steel x
15 2 Sliding plate VDI Steel x
16 2 Sliding plate VDI Steel x
17 1 Gas spring 2487.12.00750.125 x
18 2 Gas spring 2487.12.02400. □□□ x
19 x
20 2 Prismatic guide x
21 2 Stop plate x
22
23 2 Damper x
24 4 Feather key (T-nut) x
25 1 Feather key (T-nut) x
26 2 Feather key (T-nut) x
27** 2 Construction piece x
28** 2 Slide pad x
29* (not shown) 2 Curve wedge x
30* (not shown) 2 Roller block x
31 1 Locking screw x
32 2 Locking screw x
33 2 Ball-head screw x
34 2 Hexagon nut x
up to and including 45° with pre-acceleration
Optionally:
* Roll pre-acceleration (.1000. /.2000.)
** Plate pre-acceleration (.3000. /.4000.)
For inquiries or when ordering spare parts (x), we require the following data:
? Cam unit order no.
? Cam unit serial number
? Item number / Designation / Spare part
第185頁
184 Subject to alterations
AERIAL FCC
2016.25.070./.075.
SYSTEM AND SURROUNDING FORCES
Order number
a
[°]
FW
[kN]
FR*
[kN]
Fh2
[kN]
Fv2
[kN]
Fh3
[kN]
Fv3
[kN]
H2
[mm]
H3
[mm]
2016.25.07□.00.□000.02 0 1600 101.0 0 1343 1600 1343 40 300
2016.25.07□.05.□000.02 5 1600 102.9 117 1337 1477 1477 40 275
2016.25.07□.10.□000.02 10 1600 114.5 195 1103 1381 1381 75 275
2016.25.07□.15.□000.02 15 1600 116.1 290 1082 1256 1496 80 255
2016.25.07□.20.□000.02 20 1600 131.4 316 868 1188 1415 90 245
2016.25.07□.25.□000.02 25 1600 130.3 390 837 1060 1513 110 215
2016.25.07□.30.□000.02 30 1600 151.2 373 646 1013 1446 120 210
2016.25.07□.35.□000.02 35 1600 147.2 428 611 883 1529 140 210
2016.25.07□.40.□000.02 40 1600 148.1 480 572 746 1600 150 190
2016.25.07□.45.□000.02 45 1600 146.2 528 528 604 1659 170 170
2016.25.07□.50.□000.02 50 1600 124.1 708 594 321 1819 170 120
2016.25.07□.55.□000.02 55 1600 137.6 611 428 307 1739 180 115
2016.25.07□.60.□000.02 60 1600 170.7 504 291 296 1677 180 110
2016.25.07□.65.□000.02 65 1600 135.5 676 315 0 1765 190 85
2016.25.07□.70.□000.02 70 1600 163.1 547 199 0 1703 205 85
2016.25.07□.75.□000.02 75 1600 191.8 414 111 0 1656 220 85
* Retraction force values correspond to the spring-generated retraction force at the working point point
The forces Fh2, FV2 as well as Fh3, FV3 act on the tool environment at maximum working force FW.
第186頁
Subject to alterations 185
AERIAL FCC
2016.25.070./.075.
FORCE DIAGRAM
shouldered
Width 700 mm
0° 105 105 105 70 105 105 105
Height
225 mm
45 60 77 211 654 211 77 60
45 72 97 336 1044 336 97 72
45 83 117 543 1435 543 117 83
45 94 136 653 1633 653 136 94
45 105 156 451 1207 451 156 105
Support with feather key
Width 700 mm
0° 40 40 40 20 40 40 40
Height
225 mm
45 48 46 63 131 63 46 48
45 58 58 101 209 101 58 58
45 66 70 163 287 163 70 66
45 75 82 196 327 196 82 75
45 84 94 135 241 135 94 84
Width 700 mm
5° 105 105 105 70 105 105 105
Height
225 mm
45 65 84 242 732 242 84 65
45 78 108 370 1100 370 108 78
45 89 129 566 1469 566 129 89
45 99 143 650 1620 650 143 99
45 108 158 458 1219 458 158 108
Width 700 mm
5° 105 105 105 70 105 105 105
Height
225 mm
45 52 51 80 176 80 51 52
45 62 65 122 264 122 65 62
45 71 77 187 352 187 77 71
45 79 86 215 389 215 86 79
45 87 95 151 293 151 95 87
Width 700 mm
10° 105 105 105 70 105 105 105
Height
225 mm
45 69 92 274 810 274 92 69
45 83 119 404 1156 404 119 83
45 95 141 589 1502 589 141 95
45 103 150 648 1607 648 150 103
45 112 160 466 1231 466 160 112
Width 700 mm
10° 105 105 105 70 105 105 105
Height
225 mm
45 55 55 99 227 99 55 55
45 67 71 145 324 145 71 67
45 76 85 212 421 212 85 76
45 83 90 233 450 233 90 83
45 89 96 168 345 168 96 89
Width 700 mm
15° 105 105 105 70 105 105 105
Height
225 mm
45 60 61 122 290 122 61 60
45 72 79 174 395 174 79 72
45 83 94 243 500 243 94 83
45 88 96 256 519 256 96 88
45 94 99 188 405 188 99 94
Width 700 mm
20° 105 105 105 70 105 105 105
Height
225 mm
45 79 109 344 984 344 109 79
45 96 143 481 1291 481 143 96
45 110 169 648 1598 648 169 110
45 115 167 655 1610 655 167 115
45 121 166 490 1279 490 166 121
Width 700 mm
20° 105 105 105 70 105 105 105
Height
225 mm
45 63 65 145 354 145 65 63
45 77 86 202 465 202 86 77
45 88 101 272 575 272 101 88
45 92 100 275 580 275 100 92
45 97 100 206 460 206 100 97
Width 700 mm
25° 105 105 105 70 105 105 105
Height
225 mm
45 84 117 376 1064 376 117 84
45 102 154 515 1348 515 154 102
45 116 181 672 1632 672 181 116
45 120 174 652 1597 652 174 120
45 124 168 497 1292 497 168 124
Width 700 mm
25° 105 105 105 70 105 105 105
Height
225 mm
45 67 70 169 426 169 70 67
45 82 93 232 539 232 93 82
45 93 109 302 653 302 109 93
45 96 105 293 639 293 105 96
45 99 101 224 517 224 101 99
Width 700 mm
15° 105 105 105 70 105 105 105
Height
225 mm
45 75 101 312 905 312 101 75
45 90 132 446 1234 446 132 90
45 104 156 624 1564 624 156 104
45 110 160 657 1623 657 160 110
45 117 164 482 1267 482 164 117
第187頁
186 Subject to alterations
AERIAL FCC
2016.25.070./.075.
FORCE DIAGRAM
shouldered
Width 700 mm
30° 105 105 105 70 105 105 105
Height
225 mm
45 84 119 390 1092 390 119 84
45 103 158 525 1341 525 158 103
45 117 185 664 1591 664 185 117
45 119 173 620 1511 620 173 119
45 122 162 482 1245 482 162 122
Support with feather key
Width 700 mm
30° 105 105 105 70 105 105 105
Height
225 mm
45 67 74 187 480 187 74 67
45 82 98 252 590 252 98 82
45 94 114 319 700 319 114 94
45 96 107 298 665 298 107 96
45 98 100 231 548 231 100 98
Width 700 mm
35° 105 105 105 70 105 105 105
Height
225 mm
45 88 125 417 1157 417 125 88
45 107 167 553 1382 553 167 107
45 122 195 680 1608 680 195 122
45 123 178 612 1484 612 178 123
45 124 162 485 1245 485 162 124
Width 700 mm
35° 105 105 105 70 105 105 105
Height
225 mm
45 70 80 213 555 213 80 70
45 86 107 282 663 282 107 86
45 98 125 347 772 347 125 98
45 98 114 312 712 312 114 98
45 99 104 247 597 247 104 99
Width 700 mm
40° 105 105 105 70 105 105 105
Height
225 mm
45 90 127 425 1170 425 127 90
45 110 167 566 1407 566 167 110
45 125 193 674 1595 674 193 125
45 123 176 599 1462 599 176 123
45 121 160 474 1227 474 160 121
Width 700 mm
40° 105 105 105 70 105 105 105
Height
225 mm
45 72 84 230 609 230 84 72
45 88 110 305 732 305 110 88
45 100 127 364 830 364 127 100
45 98 116 324 760 324 116 98
45 97 106 256 638 256 106 97
Width 700 mm
45° 105 105 105 70 105 105 105
Height
225 mm
45 75 89 252 676 252 89 75
45 92 116 336 818 336 116 92
45 104 132 388 904 388 132 104
45 100 121 341 822 341 121 100
45 96 110 269 690 269 110 96
Width 700 mm
50° 105 105 105 70 105 105 105
Height
225 mm
45 95 133 450 1220 450 133 95
45 118 170 603 1486 603 170 118
45 133 193 674 1601 674 193 133
45 125 176 586 1444 586 176 125
45 116 159 462 1213 462 159 116
Width 700 mm
50° 105 105 105 70 105 105 105
Height
225 mm
45 76 93 270 732 270 93 76
45 94 119 362 892 362 119 94
45 107 135 404 961 404 135 107
45 100 123 352 866 352 123 100
45 93 112 277 728 277 112 93
Width 700 mm
55° 105 105 105 70 105 105 105
Height
225 mm
45 97 135 458 1234 458 135 97
45 121 170 617 1512 617 170 121
45 136 191 668 1589 668 191 136
45 125 174 574 1421 574 174 125
45 113 158 451 1195 451 158 113
Width 700 mm
55° 105 105 105 70 105 105 105
Height
225 mm
45 78 98 288 790 288 98 78
45 97 122 388 967 388 122 97
45 109 138 421 1017 421 138 109
45 100 126 362 910 362 126 100
45 90 113 284 764 284 113 90
Width 700 mm
45° 105 105 105 70 105 105 105
Height
225 mm
45 93 132 441 1206 441 132 93
45 115 170 590 1460 590 170 115
45 130 195 681 1614 681 195 130
45 125 178 599 1467 599 178 125
45 120 161 472 1232 472 161 120
第188頁
Subject to alterations 187
AERIAL FCC
2016.25.070./.075.
FORCE DIAGRAM
shouldered
Width 700 mm
60° 105 105 105 70 105 105 105
Height
225 mm
45 101 140 475 1271 475 140 101
45 126 173 642 1566 642 173 126
45 142 193 674 1606 674 193 142
45 127 176 572 1425 572 176 127
45 112 159 449 1198 449 159 112
Support with feather key
Width 700 mm
60° 105 105 105 70 105 105 105
Height
225 mm
45 81 104 313 864 313 104 81
45 101 128 424 1065 424 128 101
45 113 143 445 1092 445 143 113
45 101 130 378 969 378 130 101
45 89 117 296 815 296 117 89
Width 700 mm
65° 105 105 105 70 105 105 105
Height
225 mm
45 105 145 492 1309 492 145 105
45 132 176 667 1622 667 176 132
45 147 195 679 1623 679 195 147
45 129 177 570 1427 570 177 129
45 110 160 446 1201 446 160 110
Width 700 mm
65° 105 105 105 70 105 105 105
Height
225 mm
45 84 110 339 943 339 110 84
45 105 134 461 1168 461 134 105
45 118 148 469 1168 469 148 118
45 103 135 393 1028 393 135 103
45 88 121 308 865 308 121 88
Width 700 mm
70° 105 105 105 70 105 105 105
Height
225 mm
45 104 143 487 1287 487 143 104
45 131 171 663 1604 663 171 131
45 146 188 654 1566 654 188 146
45 125 171 542 1365 542 171 125
45 104 154 423 1150 423 154 104
Width 700 mm
70° 105 105 105 70 105 105 105
Height
225 mm
45 83 111 350 978 350 111 83
45 105 133 477 1219 477 133 105
45 117 146 471 1190 471 146 117
45 100 133 390 1038 390 133 100
45 83 120 304 874 304 120 83
Width 700 mm
75° 105 105 105 70 105 105 105
Height
225 mm
45 84 115 368 1031 368 115 84
45 106 135 502 1292 502 135 106
45 118 147 481 1231 481 147 118
45 99 134 394 1064 394 134 99
45 80 120 306 896 306 120 80
Width 700 mm
75° 105 105 105 70 105 105 105
Height
225 mm
45 105 143 490 1289 490 143 105
45 133 169 670 1615 670 169 133
45 148 184 642 1539 642 184 148
45 124 167 525 1330 525 167 124
45 99 150 408 1120 408 150 99
第189頁
188 Subject to alterations
第190頁
189
AERIAL FCC
2016.25.080./085.
Working width: 800/850 mm
Performance class: 1700 kN
第191頁
190 Subject to alterations
AERIAL FCC
2016.25.080./.085.
SIZE TABLE
第192頁
Subject to alterations 191
AERIAL FCC
2016.25.080./.085.
SIZE TABLE
Order No.
2016.25.8□0.
L**
[mm]
B***
[mm]
H
[mm]
H1
[mm]
HW
[mm]
L1
[mm]
L2
[mm]
L3
[mm]
L4
[mm]
L5
[mm]
D**
[mm]
a
[°]
b
[°]
δ
[°]
SW*
[mm]
SWA*
[mm]
SS
[mm]
SP*
[mm]
SPA*
[mm]
00.□000.02 395 8□0 400 208 220 365 370 280 305 80 395 0 50 45 - 45.7 100 - 95.2
05.□000.02 409.1 8□0 400 209 220 367.03 385 297.03 308 80 413.84 5 45 50 - 53.8 100 - 95.8
10.□000.02 428 8□0 400 208.61 220 374.12 385 304.12 302 80 434.66 10 45 45 - 56.6 100 - 95.5
15.□000.02 441.4 8□0 400 218.84 220 376.22 405 316.22 300 80 450.04 15 40 50 - 65.5 100 - 97.2
20.□000.02 449.3 8□0 400 229.69 220 373.27 410 298.27 270 80 459.32 20 40 45 - 68.8 100 - 99.8
25.□000.02 456.6 8□0 400 236.16 220 370.22 420 305.22 263 80 465.33 25 35 50 - 74.3 95 - 98.4
30.□000.02 458 8□0 400 243.22 220 362.01 425 312.01 258 80 465.12 30 35 45 - 79.5 95 - 103.2
35.□000.02 458.5 8□0 400 250.86 220 353.6 440 318.6 253 80 463.54 35 30 50 - 81.4 85 - 97.5
40.□000.02 462.9 8□0 400 259.08 220 349.93 450 324.93 247 80 464.59 40 25 55 - 93.0 85 - 104.0
45.□000.02 461.2 8□0 400 262.83 220 340.96 455 330.96 243 80 456.94 45 20 60 - 100.2 80 - 105.7
50.□000.02 483.2 8□0 400 267.09 220 356.64 480 336.64 264 80 463.85 50 10 - 107.2 - 70 94.3 -
55.□000.02 475.1 8□0 400 271.83 220 331.93 460 341.93 260 80 443.05 55 10 - 103.0 - 60 94.8 -
60.□000.02 480 8□0 400 277.01 220 316.78 470 326.78 237 80 428.29 60 10 - 108.3 - 55 103.4 -
65.□000.02 490 8□0 400 282.6 220 281.17 440 331.17 234 80 404.94 65 0 - 106.5 - 45 96.5 -
70.□000.02 505 8□0 400 288.54 220 265.05 435 335.05 232 80 391.79 70 0 - 117.0 - 40 109.9 -
75.□000.02 515 8□0 400 294.81 220 248.39 425 338.39 230 80 379.05 75 0 - 115.9 - 30 112.0 -
* Values rounded
** Values L, D measured for option with shouldered working surface
*** 8□0 = 800 or 850 mm
Mounting cam base:
Hexagon socket head cap screws DIN EN ISO 4762 8x M20 / Strength class min. 8.8
Dowel pins DIN EN ISO 8735 2x ?16
Mounting cam driver:
Hexagon socket head cap screws DIN EN ISO 4762 2x4 M16 / Strength class min. 8.8
Dowel pins DIN EN ISO 8735 2x2 ?12
第193頁
192 Subject to alterations
AERIAL FCC
2016.25.080./.085.
EXPLODED VIEW
第194頁
Subject to alterations 193
AERIAL FCC
2016.25.080./.085.
PARTS LIST
Position Piece Designation Material spare part
1 1 Slider
2.1 1 Driver, left
2.2 1 Driver, right
3 1 Slider cam base
4.1 1 Clamp, left x
4.2 1 Clamp, right x
5.1 1 Positive return, left x
5.2 1 Positive return, right x
6 4 Sliding plate VDI Bronze with solid lubricant x
7 2 Sliding plate VDI Bronze with solid lubricant x
8 2 Sliding plate VDI Bronze with solid lubricant x
9 2 Sliding plate VDI Bronze with solid lubricant x
10 2 Sliding plate VDI Bronze with solid lubricant x
11 2 Sliding plate VDI Bronze with solid lubricant x
12** 2 Sliding plate VDI Bronze with solid lubricant x
13 2 Sliding plate VDI Steel x
14 2 Sliding plate VDI Steel x
15 2 Sliding plate VDI Steel x
16 2 Sliding plate VDI Steel x
17 2 Gas spring 2487.12.00500.125 x
18 3 Gas spring 2487.12.02400.□□□ x
19 2 Cover strip x
20 2 Prismatic guide x
21 2 Stop plate x
22 1 Centre guide x
23 2 Damper x
24 4 Feather key (T-nut) x
25 1 Feather key (T-nut) x
26 2 Feather key (T-nut) x
27** 2 Construction piece x
28** 2 Slide pad x
29* (not
shown) 2 Curve wedge x
30* (not
shown) 2 Roller block x
31 2 Locking screw x
32 3 Locking screw x
33 2 Ball-head screw x
34 2 Hexagon nut x
up to and including 45° with pre-acceleration
Optionally:
* Roll pre-acceleration (.1000. /.2000.)
** Plate pre-acceleration (.3000. /.4000.)
For inquiries or when ordering spare parts (x), we require the following data:
? Cam unit order no.
? Cam unit serial number
? Item number / Designation / Spare part
第195頁
194 Subject to alterations
AERIAL FCC
2016.25.080./.085.
SYSTEM AND SURROUNDING FORCES
Order number
a
[°]
FW
[kN]
FR*
[kN]
Fh2
[kN]
Fv2
[kN]
Fh3
[kN]
Fv3
[kN]
H2
[mm]
H3
[mm]
2016.25.08□.02.□000.02 0 1700 149.3 0 1426 1700 1426 40 300
2016.25.08□.05.□000.02 5 1700 152.3 124 1421 1569 1569 40 275
2016.25.08□.10.□000.02 10 1700 169.6 207 1172 1467 1467 75 275
2016.25.08□.15.□000.02 15 1700 172.3 308 1150 1334 1590 80 255
2016.25.08□.20.□000.02 20 1700 195.1 407 1119 1190 1700 90 245
2016.25.08□.25.□000.02 25 1700 193.9 415 890 1126 1608 110 215
2016.25.08□.30.□000.02 30 1700 225.1 396 687 1076 1537 120 210
2016.25.08□.35.□000.02 35 1700 219.4 455 649 938 1624 140 210
2016.25.08□.40.□000.02 40 1700 221.1 510 607 793 1700 150 190
2016.25.08□.45.□000.02 45 1700 218.6 561 561 642 1763 170 170
2016.25.08□.50.□000.02 50 1700 186.1 752 631 341 1933 170 120
2016.25.08□.55.□000.02 55 1700 206.6 649 455 326 1847 180 115
2016.25.08□.60.□000.02 60 1700 256.5 536 309 314 1782 180 110
2016.25.08□.65.□000.02 65 1700 204.3 718 335 0 1876 190 85
2016.25.08□.70.□000.02 70 1700 246.0 581 212 0 1809 205 85
2016.25.08□.75.□000.02 75 1700 289.9 440 118 0 1760 220 85
* Retraction force values correspond to the spring-generated retraction force at the working point point
The forces Fh2, FV2 as well as Fh3, FV3 act on the tool environment at maximum working force FW.
第196頁
Subject to alterations 195
AERIAL FCC
2016.25.080./.085.
FORCE DIAGRAM
shouldered
Width 800 mm
0° 120 120 120 80 120 120 120
Height
225 mm
45 76 113 335 869 335 113 76
45 94 145 491 1310 491 145 94
45 108 169 689 1680 689 169 108
45 114 169 703 1705 703 169 114
45 120 169 504 1306 504 169 120
Support with feather key
Width 800 mm
0° 120 120 120 80 120 120 120
Height
225 mm
45 61 68 100 174 100 68 61
45 75 87 147 262 147 87 75
45 87 101 207 336 207 101 87
45 91 101 211 341 211 101 91
45 96 102 151 261 151 102 96
Width 800 mm
5° 120 120 120 80 120 120 120
Height
225 mm
45 79 118 354 926 354 118 79
45 97 152 512 1345 512 152 97
45 112 178 705 1703 705 178 112
45 117 175 705 1704 705 175 117
45 123 172 514 1322 514 172 123
Width 800 mm
5° 120 120 120 80 120 120 120
Height
225 mm
45 63 71 117 222 117 71 63
45 78 91 169 323 169 91 78
45 90 107 233 409 233 107 90
45 94 105 233 409 233 105 94
45 98 103 170 317 170 103 98
Width 800 mm
10° 120 120 120 80 120 120 120
Height
225 mm
45 81 123 374 984 374 123 81
45 100 160 533 1380 533 160 100
45 116 186 721 1725 721 186 116
45 121 180 708 1703 708 180 121
45 126 174 524 1339 524 174 126
Width 800 mm
10° 120 120 120 80 120 120 120
Height
225 mm
45 65 74 135 275 135 74 65
45 80 96 192 386 192 96 80
45 93 112 259 483 259 112 93
45 97 108 255 477 255 108 97
45 101 104 189 375 189 104 101
Width 800 mm
15° 120 120 120 80 120 120 120
Height
225 mm
45 66 75 151 327 151 75 66
45 82 99 212 444 212 99 82
45 94 115 282 549 282 115 94
45 97 109 272 535 272 109 97
45 101 104 204 426 204 104 101
Width 800 mm
20° 120 120 120 80 120 120 120
Height
225 mm
45 84 130 402 1069 402 130 84
45 104 170 561 1410 561 170 104
45 120 198 732 1721 732 198 120
45 124 186 694 1655 694 186 124
45 128 174 529 1334 529 174 128
Width 800 mm
20° 120 120 120 80 120 120 120
Height
225 mm
45 67 78 169 385 169 78 67
45 83 102 235 508 235 102 83
45 96 119 307 620 307 119 96
45 99 112 291 596 291 112 99
45 102 104 222 480 222 104 102
Width 800 mm
25° 120 120 120 80 120 120 120
Height
225 mm
45 87 136 425 1135 425 136 87
45 108 179 587 1457 587 179 108
45 125 208 754 1759 754 208 125
45 128 193 703 1670 703 193 128
45 132 178 543 1363 543 178 132
Width 800 mm
25° 120 120 120 80 120 120 120
Height
225 mm
45 70 81 191 454 191 81 70
45 87 108 264 583 264 108 87
45 100 125 339 704 339 125 100
45 103 116 316 668 316 116 103
45 106 107 244 545 244 107 106
Width 800 mm
15° 120 120 120 80 120 120 120
Height
225 mm
45 82 126 387 1022 387 126 82
45 102 165 545 1389 545 165 102
45 117 191 723 1715 723 191 117
45 122 182 698 1671 698 182 122
45 126 173 524 1331 524 173 126
第197頁
196 Subject to alterations
AERIAL FCC
2016.25.080./.085.
FORCE DIAGRAM
shouldered
Width 800 mm
30° 120 120 120 80 120 120 120
Height
225 mm
45 90 141 445 1191 445 141 90
45 112 187 608 1491 608 187 112
45 128 217 769 1781 769 217 128
45 132 198 705 1669 705 198 132
45 135 180 553 1379 553 180 135
Support with feather key
Width 800 mm
30° 120 120 120 80 120 120 120
Height
225 mm
45 72 87 213 524 213 87 72
45 89 116 292 656 292 116 89
45 103 134 369 784 369 134 103
45 105 123 339 734 339 123 105
45 108 112 265 607 265 112 108
Width 800 mm
35° 120 120 120 80 120 120 120
Height
225 mm
45 87 138 438 1178 438 138 87
45 108 183 594 1440 594 183 108
45 125 213 741 1702 741 213 125
45 128 192 669 1575 669 192 128
45 130 172 531 1318 531 172 130
Width 800 mm
35° 120 120 120 80 120 120 120
Height
225 mm
45 70 88 224 566 224 88 70
45 87 117 303 691 303 117 87
45 100 136 378 817 378 136 100
45 102 123 341 756 341 123 102
45 104 110 271 633 271 110 104
Width 800 mm
40° 120 120 120 80 120 120 120
Height
225 mm
45 90 139 451 1202 451 139 90
45 112 184 608 1467 608 184 112
45 129 212 738 1695 738 212 129
45 128 191 658 1556 658 191 128
45 127 170 522 1303 522 170 127
Width 800 mm
40° 120 120 120 80 120 120 120
Height
225 mm
45 72 92 244 625 244 92 72
45 90 121 328 763 328 121 90
45 103 140 399 882 399 140 103
45 102 126 356 809 356 126 102
45 102 112 282 677 282 112 102
Width 800 mm
45° 120 120 120 80 120 120 120
Height
225 mm
45 74 96 267 693 267 96 74
45 94 127 358 845 358 127 94
45 107 145 423 955 423 145 107
45 104 130 373 869 373 130 104
45 100 115 295 728 295 115 100
Width 800 mm
50° 120 120 120 80 120 120 120
Height
225 mm
45 96 144 486 1274 486 144 96
45 122 188 649 1551 649 188 122
45 139 215 746 1714 746 215 139
45 131 191 650 1547 650 191 131
45 124 167 513 1298 513 167 124
Width 800 mm
50° 120 120 120 80 120 120 120
Height
225 mm
45 77 101 292 765 292 101 77
45 97 132 390 931 390 132 97
45 111 151 448 1028 448 151 111
45 105 134 390 928 390 134 105
45 99 117 308 779 308 117 99
Width 800 mm
55° 120 120 120 80 120 120 120
Height
225 mm
45 99 147 504 1311 504 147 99
45 127 191 670 1594 670 191 127
45 144 217 750 1723 750 217 144
45 133 192 646 1542 646 192 133
45 122 166 509 1295 509 166 122
Width 800 mm
55° 120 120 120 80 120 120 120
Height
225 mm
45 80 106 318 839 318 106 80
45 101 137 422 1020 422 137 101
45 116 156 473 1103 473 156 116
45 106 138 407 987 407 138 106
45 97 120 321 829 321 120 97
Width 800 mm
45° 120 120 120 80 120 120 120
Height
225 mm
45 93 142 469 1238 469 142 93
45 117 186 629 1509 629 186 117
45 134 214 742 1705 742 214 134
45 130 191 655 1552 655 191 130
45 125 169 518 1300 518 169 125
第198頁
Subject to alterations 197
AERIAL FCC
2016.25.080./.085.
FORCE DIAGRAM
shouldered
Width 800 mm
60° 120 120 120 80 120 120 120
Height
225 mm
45 102 148 517 1335 517 148 102
45 131 191 685 1622 685 191 131
45 148 217 747 1716 747 217 148
45 133 190 636 1523 636 190 133
45 118 163 499 1279 499 163 118
Support with feather key
Width 800 mm
60° 120 120 120 80 120 120 120
Height
225 mm
45 81 110 341 908 341 110 81
45 104 141 452 1103 452 141 104
45 119 160 493 1167 493 160 119
45 107 141 420 1035 420 141 107
45 95 121 330 870 330 121 95
Width 800 mm
65° 120 120 120 80 120 120 120
Height
225 mm
45 103 148 526 1347 526 148 103
45 133 190 693 1634 693 190 133
45 151 214 737 1692 737 214 151
45 133 187 619 1488 619 187 133
45 114 159 485 1252 485 159 114
Width 800 mm
65° 120 120 120 80 120 120 120
Height
225 mm
45 83 113 363 970 363 113 83
45 107 144 478 1176 478 144 107
45 121 163 508 1218 508 163 121
45 106 142 427 1072 427 142 106
45 91 121 335 901 335 121 91
Width 800 mm
70° 120 120 120 80 120 120 120
Height
225 mm
45 106 149 539 1371 539 149 106
45 137 190 708 1661 708 190 137
45 155 214 734 1685 734 214 155
45 133 185 609 1469 609 185 133
45 111 156 476 1237 476 156 111
Width 800 mm
70° 120 120 120 80 120 120 120
Height
225 mm
45 84 117 388 1042 388 117 84
45 110 148 510 1263 510 148 110
45 124 167 528 1280 528 167 124
45 106 144 438 1116 438 144 106
45 89 122 342 940 342 122 89
Width 800 mm
75° 120 120 120 80 120 120 120
Height
225 mm
45 87 122 418 1127 418 122 87
45 114 154 547 1364 547 154 114
45 128 172 553 1355 553 172 128
45 108 148 453 1171 453 148 108
45 87 124 353 987 353 124 87
Width 800 mm
75° 120 120 120 80 120 120 120
Height
225 mm
45 109 152 557 1409 557 152 109
45 142 193 730 1705 730 193 142
45 160 215 737 1693 737 215 160
45 135 185 604 1463 604 185 135
45 109 155 471 1233 471 155 109
第199頁
198 Subject to alterations
第200頁
199
AERIAL FCC
2016.25.090./095.
Working width: 900/950 mm
Performance class: 1800 kN
百萬用戶使用云展網(wǎng)進行電子書本制作，只要您有文檔，即可一鍵上傳，自動生成鏈接和二維碼(獨立電子書)，支持分享到微信和網(wǎng)站！
其他案例
百萬用戶使用云展網(wǎng)進行電子書本制作，只要您有文檔，即可一鍵上傳，自動生成鏈接和二維碼(獨立電子書)，支持分享到微信和網(wǎng)站！
免費制作
{{modalTitle}}
QQ
QQ空間
豆瓣
復制鏈接
{{item.title}}
x
{{item.desc}}
{{item.title}}
{{toast}}
