樂高42083--布加迪燈光安裝教程

布加迪遙控?zé)艚M

燈組包含：A組車頭燈、B組室內燈.發動機、C組車尾燈、

D尾翼燈車牌燈、E組底盤燈。遙控器、接收板、鋰電池、

充電線

1.首先取出A包，按照圖片把車頭燈的零件拆出，然后按

照以下圖片安裝即可。

Lego 42 08 3- -Bu gatti L ight I ns ta llation T ut or ial

B ugatti Remo te Co nt rol Light Set The lamp group

i ncl ud es : A gro up hea dligh ts , B gro up i nd oor

li ghts.E ng ine, Group C rear lights, T he D

ta ilwing ligh t lic en se plate light , th e E group

chass is li gh t.Remo te c on trol, recei vi ng bo ard,

lithi um b at tery, Chargi ng li ne

T he 1 . fir st r em ov es the A pac kage, remov es t he

headligh t par ts f ol lowin g the pict ur e, an d th en

presses Inst al l it in th e pi ct ur e below.

取出車頭燈條，撕開背面白色的膠紙粘貼在前燈的零件部位

上，然后用鑷子按緊燈直到緊貼大燈底部安裝完成，復原車

頭并將線頭導到到室內

Re mo ve the h ea dlight str ip , tea r the w hi te tape

on th e bac k an d pas te the parts of th e he adligh t

On , th en press the lamp with tweez er s unt il

ins ta lled close to the bottom of the head li gh t

to res to re t he ca r Hea d an d gui de the thread head

to th e ro om

2.按照圖片所示把零件拉開，然后把整個蓋子翻上，如圖所示

2. pulls the part as shown in the picture and then flip the entire

cover as shown

取出燈組B和發動機蓋子，將末端燈片貼在蓋子下方。

剩余燈組穿到室內，貼于室內頂部如圖所示。端子口接到接收板B口

Re move the light s et B and engine lid and attac h

t he end light und er th e li d.

Th e re mainin g lig ht g ro ups are wo rn indoors a nd a ff ix ed

to t he to p of th e cha mb er as sho wn in Fi g.Termin al po rt

is conne ct ed t o the r ec eiving board B port

取出C組燈，將尾燈配件拆下

R em ove the group C li ghts and remove th e tail li ght fittin gs

燈片貼到左右兩側，復原尾部將線頭穿回室內端子口接到接收板C口

St ick to th e lef t an d ri ght sides, r esto re t he re ar w ill

wear the wire b ack to the indoo r ter mi nal port to the

port of the receivi ng bo ar d C

取出D組燈片，將第一片燈組貼到尾翼下方。

第二片燈組貼到布加迪標頂部

Remove t he D set light and post the first l ig ht s et

below the tail.

Th e sec on d la mp set is p ost ed to th e to p of the B ug at ti logo

復原車子蓋板

Restore t he ca r co ve r pla te

取出E組燈，拆下車頭配件

將E組燈的單片燈貼到配件中間，線頭留到左側。

R em ove th e gr oup E li ghts and remove the head fit ti ng s

Po st th e E lam p to the midd le of the acc ess ory and

l ea ve the th read to the left.

復原配件后將車子翻過來，安裝底盤氛圍燈

Rep ai r th e acc essori es an d tur n th e car o ve r to

ins ta ll th e ch assis atmosp he re light

將線頭穿回室內 拆下車尾排氣口，將最后一組燈片貼到指定位置

復原排氣口

We ar th e li ne ba ck i ndoors to remove the rear exha us t and

p ost the last set of li ghts to the specifi ed lo ca tion

Resum e ex ha ust po rt

線頭端子口接到接收板，裝上鋰電池、燈組安裝完成

The cabl e ter mi nal port is connected t o the rece ivi ng

bo ard an d in stalle d wit h li th ium battery and lam p set

將線整理下藏到車座后方，

Collec t the line to the car behin d the s ea t,

注意：接收板藏太深可能會影響遙控的控制噢

電池充電

B at tery chargi ng